We will be refreshing and updating the forum over the next few weeks. You can still register and talk sleds...

Lift Kit Install (Part 2)

Talk about the oldies, restore, repair, etc.

Moderators: Old School, harryparatestis

Post Reply
THX_138
Posts: 21
Joined: December 29th, 2007, 12:13 pm

Lift Kit Install (Part 2)

Post by THX_138 »

These are some pictures showing the difference from stock height
to lifted height with Danthemans lift kit installed.
Sorry about the quality of some of the pictures :oops:

Difference from the front



Image

Stock from the side

Image

Lifted from the side

Image


Difference from the rear


Image

Complete

Image

To conclude I MUST add that nothing has ridden our yard since the
last snow. It was about 6-8 inches of a granulated powder witha thin
crust of freezing rain on top....about enough to hold up a squirrel or
a cat but not a dog.

I figured, what the heck...give it a shot! Across the driveway he
went, over the small snowbank and into the depths!!!!!....LOL

Seriously though....into the depths he went... and kept on going
without a struggle or issue at all. Even the first time he came to a
stop in the fresh snow to look back at me completely bewildered
WHY his sled wasn't getting stuck...
it took right off without any problems!

Lifting a Kitty is definately a cure all!!!!!!
1121racinkitty
Posts: 63
Joined: March 6th, 2005, 7:37 pm
Location: NEW BERLIN,WI.WHERE IT ALL STARTED!!!!!!!!!!

Post by 1121racinkitty »

ITS BECAUSE DAN IS THE MAN!!!!!!
KITTY CATS ROCK!
User avatar
dantheman
Posts: 91
Joined: March 1st, 2005, 8:04 pm

wow no shit

Post by dantheman »

well i must say thats the first i have heard about any of that stuff needing to be done and ive sold quite a few of these things
somewhere along the line someone changed your spindles ,the originals on that older sled had 5/16 bolts thru the skis. the top thread on most of the sleds are 5-16-18, how you ended up with a fine thread i dont know maybe they ran out of course thread bolts at arctic cat that day. ive also seen some plates with weld nuts and some without, ive also had a few people call me and tell me they had an m8 metric thread in top of thier spindle.
You didnt need the third bolt at all in the tunnel thats why i removed it from the original pattern the 94 and up only have 2 bolts
as far as having to cut the spindle to clear the saddle i will make a change to the laser pattern for that extra room so the next guys dont have to grind anything.
THere does seem to be some differences in some of the parts on these kitties , i dont know if it had to do with switching parts suppliers or what but i have had a lot of people tell me it bolted right in in 20 minutes with absolutely no issues.

SORRY ABOUT THE EXTRA WORK
Thanks for the pictures its helps quite a bit, and it also helps make improvements
Dan
THX_138
Posts: 21
Joined: December 29th, 2007, 12:13 pm

Post by THX_138 »

I must have a Kitty that was built on a Saturday close to quitting time :lol:
Last edited by THX_138 on February 1st, 2008, 8:31 pm, edited 1 time in total.
User avatar
dantheman
Posts: 91
Joined: March 1st, 2005, 8:04 pm

sales

Post by dantheman »

i do not need to increase my sales i cant ever seem to make these fast enough as it is

dan
timartin
Posts: 2
Joined: April 22nd, 2008, 6:44 am
Location: Canada (NB)

How much does it lift from stock

Post by timartin »

Great Job, looks very good...did you mesure how much it lifted the kitty. I have 2 kitty and I would like to lift it myself...as a project and would like to know how much inches more at the back and how much at the ski spindles...thanks
flynmx
Posts: 2
Joined: September 25th, 2008, 10:46 pm
Location: Neenah,WI

Dans Lift Kit

Post by flynmx »

Dan, wondering on your current price for the lift kit? Also do you still need to shorten the shafts or does it just bolt together?
User avatar
Haggs21
Posts: 19
Joined: December 16th, 2015, 1:19 am
Location: Garden City, Mi 48135

I WANT A KIT SOOOO BAD.

Post by Haggs21 »

I live in Michigan. Does Dan the Man still exist?

Does anyone have the File to make your own? I may be able to get a buddy to make at his machine shop if I had the CAD file or whatever...PLEASE come out of retirement...
User avatar
dantheman
Posts: 91
Joined: March 1st, 2005, 8:04 pm

kit prints

Post by dantheman »

User avatar
Haggs21
Posts: 19
Joined: December 16th, 2015, 1:19 am
Location: Garden City, Mi 48135

So cool.

Post by Haggs21 »

So cool. Thanks for the detailed share. I cant wait to make a pair. Thank for the files Dan
Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests